Heidra 200
The Heidra 200 hydraulic submersible pump is a self-contained, diesel powered 8" (200mm) pump available for heavy duty municipal and industrial dewatering and solids handling pumping applications. The Heidra 200 offers flow rates up to 3100 gpm (703.7 M3/hr.) with up to 180' (54.9M) of total dynamic head and solids handling capability of 3-1/8" (79mm) in diameter. The unit consists of a sturdy cast iron submersible pumpend and hydraulic power pack mounted on a rugged steel skid. A variable displacement hydraulic piston pump on the power pack delivers hydraulic fluid to a fixed displacement piston motor that drives the pumpend’s shaft, bearings, and cast steel impeller. Simple engine throttle adjustments allow changes to pump flow and head performance.
- Rugged construction of cast iron pumpend with cast chromium steel impeller.
- Flow rates to 3100 gpm (703.7 M3/hr.) and heads to 180 feet (54.9M).
- Unique double mechanical seal immersed in isolated oil bath for unlimited dry running capability.
- Integral 175 gallon (662 liter) fuel tank capacity provides over 24 hours of continuous operation.
- Safety shutdown system incorporated into engine controls prevents equipment damage from engine fault or failure.
- Impeller designed for general pumping with solids up to 3-1/8" (79mm) in diameter.
- “Quick-Disconnect” hydraulic fittings simplify setup, installation, and shutdown.
- Standard John Deere 6068T or Caterpillar 3116TA engine. Also available with other diesel engines or electric drive motor.
Submersible Pump:
Hydraulic Motor: Fixed Piston
Drive Pressure: Up to 4000 psi (276 BAR)
Hydraulic Flow: Up to 57 gpm (3.6 l/sec.)
Hydraulic Line Length: 100 feet / 30.5M (longer runs with larger hose)
Solids Handling: Up to 3-1/8" (79mm) diameter
Pump Speed: Up to 2200 rpm
Impeller Diameter: 11-3/8" (290mm)
Discharge Flange: 8" (200mm) ASA 150
Hydraulic Connections: 1-1/4" (32mm) Quick Disconnect
Strainer: Nylon coated with 2-3/4" (70mm) apertures
Power Pack:
John Deere 6068T Engine
Horsepower: 147 hp (110 kw) @ 2200 rpm
Caterpillar 3116TA Engine
Horsepower: 143 hp (107 kw) @ 2200 rpm
Fuel Tank Capacity: 175 gallons (662 liters)
Output
Hydraulic Flow: 57 gpm (3.7 l/sec.)
Pressure: 4000 psi (276 BAR)
Control: From engine speed and pressure compensated
Hydraulic System: Two pipe, open circuit
Reservoir: 80 gallon (303 liters)
Control Valve: Pressure compensated on/off valve
Connections:
1-1/4" (32mm) Quick Disconnect feed and return
1/2" (13mm) Quick Disconnect case drain
Supply Line: 125 micron, pleated gauze
Return Line: 20 micron
Heidra 200 — shown with John Deere 6068T, Skid Base
Pump Weight: 780 lbs. (354 kg.)
Complete pumpset is supplied with one each of 1-1/4" X 50' (32mm x 15.25M) high pressure feed and return hoses and one 1/2" X 50' (13mm x 15.25M) low pressure case drain hose.
Notes:
- Impeller diameter: 11-3/8" (290 mm)
- Performance curves based on diesel engine speed
- Requires hydraulic system pressure to 4000 psi (276 BAR)
Performance data based on water testing at sea level and 68° F. Larger diameter pipes may be required for maximum flows.
