Advanced Product Search
Product Lines
Models

(or press ESC or click the overlay)

Heidra 100
Heidra 100

Heidra 100

The Godwin 4" (100mm) Heidra 100 hydraulic submersible pump is a compact self-contained pumping unit featuring a diesel driven power pack and 4" (100mm) submersible hydraulic pump. With variable speed diesel engine power, the Heidra 100 can meet a variety of flow and head requirements up to 800 gpm (408.6 M3/hr.) and 120 feet (36.6M) of total dynamic head with a simple throttle adjustment. Add the ability to pass solids to 2" (50mm) diameters, dry running capabilities, a cast chromium steel impeller, and you have a rugged dewatering / solids-handling, hydraulic submersible pump ready to go anywhere.

  • Rugged construction featuring cast iron pumping chamber and cast chromium steel impeller.
  • Bearings are independent from the hydraulic gear motor – pump loads in no way affect gear motor performance.
  • Double mechanical seal in its own clean oil bath allowing for indefinite dry running. Inboard seal: silicone carbide. Outboard seal: carbon or ceramic.
  • Standard impeller designed for general pumping, slurries and sludges. Semi-recessed impeller provides greater solids-handling capabilities.
  • Standard two-bolt SAE flange gear motor connections.
  • Simple to maintain, gear motor with “plug-in” connection allows for quick changeover when required.

Submersible Pump:
Hydraulic Motor: Gear Type
Drive Pressures: 3350 psi (231 BAR)
Flow: 8.8 gpm (.56 l/sec.)
Pump Speed: Up to 2200 RPM
Impeller Diameter: 8.4" (213mm)
Solids Handling: 2" (50mm), max.
Discharge: Flanged 4" (100mm) ASA 150
Hydraulic Discharge Connections:
     3/4" (19mm) Quick Disconnect feed and return
     1/2" (13mm) Quick Disconnect case drain
Strainer: M.S. Fabrication nylon coated with 1.75" (44mm) square apertures

Power Pack:
Engine: Yanmar 3TNV88, 23 hp (17kw) @ 2000 RPM
Hydraulic System: Two pipe open circuit
Hydraulic Reservoir: 10 gallon (37.8 liter) capacity
Control: Through variable engine speed
Hydraulic Pump: Gear type
Output Flow: 8.8 gpm (.56 l/sec.)
Output pressure: Up to 3350 psi (231 BAR)
Suction Filter: 125 micron pleated gauze
Return Line Filter: 20 micron
Hydraulic Pipe Connections: 3/4" (19mm) API

Pump Casing and Suction Cover:
Aluminum or Cast Iron

Front & Rear Wearplates:
Cast Iron

Pump Shaft:
Mild Steel

Impeller:
Cast Steel

Bearing & Seal Housing:
Cast Iron

Mechanical Seal:
Double mechanical seal in oil bath
     Inboard: Silicone Carbide
     Outboard: Carbon on Ceramic

Lifting Bracket:
Fabricated Mild Steel tube & plate

Weights (approx.)
Pump
     Aluminum 90 lbs. (41 kg.)
     Cast iron 141 lbs. (64 kg.)
Power Pack 1,230 lbs. (558 kg.)

Heidra 100

Performance data listed in table and curves based on water tests at sea level and 68° F (20° C).
Larger diameter pipes may be required for maximum flows.

Heidra 100

Product Datasheets

Twitter RSS YouTube
World Headquarters: 84 Floodgate Road | Bridgeport, NJ 08014
Phone: 856.467.3636 | .(JavaScript must be enabled to view this email address) | Terms & Conditions | Privacy Policy
xylem - Let's Solve Water