Advanced Product Search
Product Lines
Models

(or press ESC or click the overlay)

Heidra 150MR

Heidra 150MR

The Godwin 6" (150mm) Heidra 150MR hydraulic submersible pump offers improved performance and operating efficiencies that cannot be matched by standard electrical submersible models. With variable speed diesel engine power, the Heidra 150MR can meet a variety of flow and head requirements up to 1900 gpm (120 l/sec.) and 160 feet (48.8M) of total dynamic head with a simple throttle adjustment. Add the ability to pass solids to 3" (75mm) in diameter, dry running capabilities, a cast chromium steel impeller, and you have a rugged dewatering/solids-handling, self-contained hydraulic submersible pump ready to go anywhere.

  • Rugged construction featuring cast iron pumping chamber and cast chromium steel impeller.
  • The pump has independent bearings from the hydraulic gear motor, so pump loads do not affect gear motor performance.
  • Double mechanical seal in its own clean oil bath allowing for indefinite dry running. Outboard seal: silicone carbide. Inboard seal: carbon or ceramic.
  • Standard impeller is designed for general pumping, slurries and sludges. Available vortex impeller provides greater solids-handling capabilities.
  • Gear motor connections are standard two-bolt SAE flange.
  • For ease of maintenance, the gear motor has a “plug-in” connection to allow for quick changeover when required.

Submersible Pump:
Hydraulic Motor: Gear Type
Drive Pressures: Up to 3500 psi (241 BAR)
Flow: Up to 32 gallons (121 liters)
Pump Speed: Up to 2200 rpm (approx.)
Impeller Diameter: 11" (279mm)
Solids Handling: 3" (75mm) in diameter
Weight: 355 lbs. (161 kg.)
Discharge: 6" (150mm) FNPT
Hydraulic Connections: 1" (25mm) Wingnut Quick Disconnect fittings
Strainer: M.S. Fabrication nylon coated with 2.75" (70mm) square apertures

Power Pack:
Engine: John Deere 4045D
     72 hp (53 kw) @ 2400 rpm
     Caterpillar 3054NA
     74 hp (55 kw) @ 2200 rpm
Hydraulic System: Two pipe open circuit
Hydraulic Reservoir Capacity: 40 gallons (151 liters)
Control: Via variable speed engine
Hydraulic Pump: Gear type
Output Flow: 32 gallons (121 liters)
Output pressure: 3500 psi (241 BAR)
Suction Filter: 125 micron pleated gauze
Return Line Filter: 20 micron
Hydraulic Pipe Connections: 1" (25mm) Wingnut Quick Disconnect fittings

Pump Casing and Suction Cover: Cast Iron
Bearing & Seal Housing and Front Wearplate: Cast Iron
Pump Shaft: Medium Carbon Steel
Impeller: Cast Steel
Rear Wearplate: Mild Steel
Mechanical Seal: Double mechanical seal in oil bath
     Outboard: Silicone Carbide
     Inboard: Carbon or Ceramic
Lifting Bracket: Fabricated Mild Steel tube & plate

Weights (approx.)
Pump 355 lbs. (161 kg.)
Power Pack 2,996 lbs. (1,359 kg.)

Heidra 150MR

Performance data from curve based on water tests at sea level and 68° F (20° C).
Larger diameter pipes may be required for maximum flows.

Heidra 150MR

Product Datasheets

Twitter RSS YouTube
World Headquarters: 84 Floodgate Road | Bridgeport, NJ 08014
Phone: 856.467.3636 | Contact Us | Terms & Conditions | Privacy Policy
xylem - Let's Solve Water